ISL267817IUZ【PDF 3/18 页】IC INTERFACE

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录2001

1页 2页 [3页]4页 5页 6页 7页

ISL267817

FN7877.2

April 19, 2012

Functional Description

The ISL267817 is based on a successive approximation register

(SAR) architecture utilizing capacitive charge redistribution

digital to analog converters (DACs). Figure 25 shows a simplified

representation of the converter. During the acquisition phase

(ACQ), the differential input is stored on the sampling capacitors

(CS). The comparator is in a balanced state since the switch

across its inputs is closed. The signal is fully acquired after tACQ

has elapsed, and the switches then transition to the conversion

phase (CONV) so the stored voltage may be converted to digital

format. The comparator will become unbalanced when the

differential switch opens and the input switches transition

(assuming that the stored voltage is not exactly at mid-scale).

The comparator output reflects whether the stored voltage is

above or below mid-scale, which sets the value of the MSB. The

SAR logic then forces the capacitive DACs to adjust up or down by

one quarter of full-scale by switching in binarily weighted

capacitors. Again, the comparator output reflects whether the

stored voltage is above or below the new value, setting the value

of the next lowest bit. This process repeats until all 12 bits have

been resolved.

An external clock must be applied to the DCLOCK pin to generate

a conversion result. The allowable frequency range for DCLOCK is

10kHz to 3.2MHz (625SPS to 200kSPS). Serial output data is

transmitted on the falling edge of DCLOCK. The receiving device

(FPGA, DSP or Microcontroller) may latch the data on the rising

edge of DCLOCK to maximize set-up and hold times.

A stable, low-noise reference voltage must be applied to the VREF

pin to set the full-scale input range and common-mode voltage. See

“Voltage Reference Input” on page 12 for more details.

ADC Transfer Function

The output coding for the ISL267817 is twos complement. The

first code transition occurs at successive LSB values (i.e., 1 LSB,

2 LSB, and so on). The LSB size is 2*VREF/4096. The ideal

transfer characteristic of the ISL267817 is shown in Figure 26.

Analog Input

The ISL267817 features a fully differential input with a nominal

full-scale range equal to twice the applied VREF voltage. Each

input swings VREF VP-P, 180° out-of-phase from one another for

a total differential input of 2*VREF (refer to Figure 27).

FIGURE 24. REFERENCE CURRENT vs TEMPERATURE (CODE = FF8h)

Typical Performance Characteristics T

A = +25°C, VCC = 5V, VREF = 2.5V, fSAMPLE = 200kHz,

fCLK =16*fSAMPLE, unless otherwise specified. (Continued)

-50

-25

100

TEMPERATURE (°C)

REFERE

CURRENT

(A)

FIGURE 25. SAR ADC ARCHITECTURAL BLOCK DIAGRAM

+IN

–IN

VREF

ACQ

CONV

ACQ

CONV

SAR

LOGIC

FIGURE 26. IDEAL TRANSFER CHARACTERISTICS

FIGURE 27. DIFFERENTIAL INPUT SIGNALING

1LSB = 2VREF/4096

100...000

100...001

100...010

111...111

000...000

000...001

011...110

011...111

ANALOG INPUT

+IN

–(–IN)

–VREF

+ LSB

+VREF

– 1LSB

+VREF

– 1LSB

ISL267817

VCM

VREF PP

+IN

–IN

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式